Do You Know What to do About Your Roof Problems

How long a roof will last is dependent on several controllable factors. The lifespan of a house-top can be extended or reduced depending on the way it is maintained by the homeowner; however, it is a fact that no matter how well it is cared for, at some point the material will deteriorate and risk structure failure. Common signs of structural roof problems include: the presence of granulation; broken shingles; and slipping or cracked shingles. All of this if not detected at an early stage could allow water to penetrate the structure and cause severe damage and premature failure of the entire roof. This top covering of the house is very susceptible to leaking; therefore, homeowners should always practice preventive maintenance and prevent any leaks from starting.

Inspections

Any damage to the integrity of the structure itself can cause susceptibility to water leakage and decay. It is vital to thoroughly inspect the house-top before any major damage occurs. Start the inspection by first checking the interior ceilings for signs of water penetration; this may come in the form of a coffee-colored stain on the ceiling or surrounding walls. Continue the inspection outside by going onto the house-top to check for any indication of structural damage. Look for missing, cracked or loose shingles, granulation, and debris accumulation.

Repairs

After conducting a thorough assessment of this top part of the house and discovering there is a problem with the structure that may require repairs, a homeowner needs to make a decision about the next step. It must be decided if an expert from a roof company is needed to perform the job or if they can make the repairs on their own. It is fairly easy for a homeowner to make minor repairs provided they have adequate knowledge regarding how to perform any required repairs.

Water Leakage

Once water staining has been observed, a leak should be suspected. The first action homeowners should take is to locate the point of water penetration. After locating this spot, a nail should be hammered into the area of the leak. The homeowner should then go outside to look for the area on the roof that needs to be repaired. If the seepage has been caused by loose flashing around a chimney or vent, all that needs to happen is to tighten the flashing with rust-resistant screws. If the cause of the leak is due to damaged shingles, the damaged shingle must be removed and replaced with a new one, ensuring that the replacement tab is larger than the damaged tab. The homeowner must remember to put roofing cement over all nail heads to secure a tight seal.

Cleaning

Sometimes a problem may be caused by the accumulation of debris on the roof or because of an algae infestation. Dark staining on the roof caused by algae can be removed simply by making a bleach solution and spraying it onto the affected area. The solution needs to soak on the area where it has been applied for 15 to 30 minutes before using a soft bristle brush to scrub off the wet section of the roof. Then, the area should be thoroughly rinsed with clear water. Remove pine needles, leaves and twigs from any area that might cause water to back up. Be sure that down-spouts are properly working.

Friedrich ES16L33 Twintemp Air conditioner

The Friedrich ES16L33 is both an air conditioner and a heater as the “twintemp” part of the name suggests. The Friedrich ES16L33 Twintemp air conditioner is a remarkable appliance for the money. With a price tag around $1000, it should offer some top of the line features, and it really does that and more. It can get you through the winter and summer in unparalleled contentment. Let’s take a peek at a few of the highlights it sports:

Ultra quiet working noise level

Unlike the noisy monoliths rattling in windows from days past, the Friedrich ES16L33 electric air conditioner does its cooling or heating work so quietly that it’s hard to tell it’s even on much of the time. This ability to function quietly is one of the hallmarks of a high end machine. You won’t be distracted by it, but simply warmed or cooled as the situation requires.

Energy Efficient

By cycling the fan with the compressor, the Friedrich ES16L33 is able to work in an energy efficient manner, saving its owner money on electric bills. Anyone who’s ever owned an air conditioner knows how they can gobble up electricity and send monthly expenses skyrocketing. This unit takes this into account and saves consumers dollars wherever possible.

Multiple heating/cooling settings

The Friedrich ES16L33 Twintemp air conditioner has 3 different heating and cooling speed settings, plus a fan only setting. These multiple settings allow for fine tuning of the comfort level of a room so that there is never a sense of being too chilly or too hot.

Thermostat

This model has a sensitive thermostat that not only monitors changes in heat levels but anticipates them. So you don’t have to wait until the room is sweltering or freezing before it turns on. You can rest assured that it will get your indoor space to a comfortable temperature and keep it there.

Rotary Controls

The rotary controls give a sense of greater control to the settings. No more worrying about sticking buttons or so called fancy touch sensitive controls that break. These controls are easy to turn and put on the desired settings.

8 way airflow control, fresh/stale air exhaust vents, and filters

This air conditioner offers unmatched control of airflow so that the air you’re breathing is always the purest and freshest it can be. It channels in the fresh air and sends the stale air outside the house with sophisticated 8 way airflow control. The Friedrich ES16L33 electric air conditioner also sports antimicrobial filters to further purify the air you’re breathing

At a cooling capacity of 16200 BTU per hour and a heating capacity of 9.8 EER, this conditioner is plenty strong. It can handle small or large rooms with ease.

The Friedrich ES16L33 is a genuinely high quality appliance that will reward consumers for their investment many times over.

Learn to Measure Your Roof and Save Money!

As a homeowner, it is important to know how much a contractor may charge for the repair or replacement of the roof of a home. An owner should know how to measure the size of the roof as well as the length of the valleys, dormers, and ridge vents to compare against any estimates that are received.

Armed with the knowledge about basic measurements, a homeowner can approximate the amount of material needed for the replacing of a roof. That knowledge can save a homeowner from the result of a miscalculation as anyone can make mistakes when calculating an estimate, even expert contractors. Knowing this simple calculation result, a homeowner can correct a contractor on the spot if there are any major discrepancies on the square footage of the roofing area.

Basic Mathematics

When measuring the roof, the result is expressed in squares. In geometry, one square is equivalent to one hundred square feet (1 = 100 square feet). So, to determine the area of a triangle, this simple geometrical equation must be remembered: area is equivalent to the length of the base times the height of the triangle in feet divided by two. The equation should look like this; (b x h)/2. For example, 40-foot (h) x 40-foot (b) divided by 2 is 40 x 40 divided by 2 equals 800 sq. feet or 8 squares.

In order to get the correct estimated measurement of the house-top, one needs to have an aerial view or rough sketch of the roof and divide it into different sections.

Step 1: Measuring Overall Area

One must first draw a diagram of the house-top. A person must get a 100-foot measuring tape, a pencil, some paper and an assistant. The assistant will hold the tip of the measuring tape while the homeowner checks and records the measurements. The sketch should include the ridge, valleys, dormers, vents, chimneys and pipes. Begin at one corner on a side and measure the dimension of the exterior walls, measuring both width and length. Most roofs have an area that extends out to cover and protect exterior walls and side known as overhangs. The overhang must be measured and added to the completed dimensions. Then the measurement should be transposed onto the diagram.

Step 2: Measuring the Pitch

The pitch is basically the steepness of a roof and is measured by determining the rise in inches per every 12 inches of horizontal length. To arrive at a multiplier that will figure into the calculations, pitch can be divided into 3 categories: low, medium and high. Low pitch is a roof that can easily be walked and the multiplier would be 1.15 to 1.25. Medium would be a rise of 5 to 9 feet for every 12 inches and would result in a multiplier of 1.25 to 1.4. The high or steep slope category covers a rise that is greater than 9 feet for every 12 inches and gives a multiplier of 1.7 and higher.

Step 3: Final Computation

After getting the dimensions, roof pitch and multiplier, the size of a homes house-top can be calculated. Take the computed overall area in square feet and multiply it by the pitch multiplier. For example, the ground dimension is equivalent to 1,104 square feet and the roof pitch is low at 1.15. The resulting equation should look like: 1,104 x 1.15 = 1,270 sq. feet. Therefore, the estimated amount of material needed for the roof is 12.7 squares. It can also be calculated by looking at the original square footage of 1,104 or 11 squares x 1.15 = 12.65. Either calculation represents the estimated squares needed for the replacement job.

Knowing how to measure a roof can give a homeowner the ability to make sure any estimate given by a contractor is very accurate and this can calculate into a large monetary savings. So learn the right way to measure that house-top and translate that information into accurate replacement cost!

How You Can Do the Garbage Bag Airflow Test

Nothing beats the coziness of your own home especially during those cold, winter nights. But when you’re freezing in it despite having a furnace then there’s a problem. A good way to check if poor air flow is the concern is to use the garbage bag airflow test.

One of the most common issues with heating and cooling equipment is poor air flow. This problem makes your heating and cooling equipment work like inefficient outdated models and this can waste a lot of your money. The two most common reasons for poor air flow: inadequate duct sizing and a dirty return air filter.

Inadequate Duct Sizing Inadequate duct sizing is usually the result of a poor installation by a contractor who might possibly not have the qualifications to perform proper sizing. This is a very common problem that a homeowner may battle for years to come and could cost thousands of dollars over the life of the equipment. It is extremely crucial that you get references before choosing a contractor.

A Dirty Return Air Filter A dirty return air filter is the easiest problem to fix. Simply change your return air conditioning filter more frequently or utilize a filter that does not restrict air flow. This simple change can lead to huge savings. How You Can Perform the Garbage Bag Air flow Test

Garbage bag airflow test is one of the easiest and cheapest methods to determine the air flow of your furnace registers, bathroom exhaust fan or clothes dryer exhaust. It’s a vital test to pinpoint the reason why your furnace isn’t providing sufficient warm air in your room. This is also important in order to determine whether your newly purchased exhaust is working at its best. The same goes when you’re having major renovations in your home that call for a change in your heating or cooling systems. It’s the cheapest way to check your furnace register and exhaust fans performance as it only requires a garbage bag. This test isn’t a precise measurement of the airflow but it is better than not conducting any test at all.

Here’s how to do the garbage bag airflow test:

1. Secure the mouth of the garbage bag using a tape right into a bent coat hanger or to a cardboard in order to keep it open.

2. Be sure to deflate the bag by crushing it flat.

3. Position the open part of the bag (mouth) over the furnace register or exhaust hood.

4. Using a stopwatch or any gadget track the number of seconds it takes for the bag to fully inflate.

If you’re using a small garbage bag that measures 66 x 91 cm, you should use the information below to determine the airflow:

Inflation time = Airflow

*2 seconds = 35L/s (75 cfm)

*4 seconds = 20 L/s (40 cfm)

*10 seconds = 10 L/s (20 cfm)

However, if you’re using a bigger garbage bag that measures 79 x 119 cm, use this data:

Inflation time = Airlfow

*2 seconds = 100 L/s (210 cfm)

*4 seconds = 50 L/s (105 cfm)

Is LifeVantage a Scam

Founded in 2003, LifeVantage Corporation is a publicly traded (ticker LFVN) MLM business specializing in scientific anti-aging products using its clinically studied Protandim supplement.

LifeVantage has a very interesting history

The company’s stock skyrocketed earlier on 2005 after they made public the clinical studies and television specials by ABC, the Today Show and PBS concerning their Protandim product in 2005, The corporation’s stock went through the roof. This early publicity sent their stock up to more than twenty dollars per share but it could not sustain it with no sales to support the hype. During this time Protantim was just obtainable by means of retail channels and it did not do well on the shelves of nutritional stores.

On May, 2009, after more than 6 months of planning and research they ventured into MLM for distribution|After more than 6 months of developing and preparation, in May of 2009. Not surprising to those who know the power of Multi-Level Marketing, LifeVantage sales have dramatically improved and with that their stock price has more than tripled from its lowest point of less than $0.10 in Nov. 2008. Still a bit too early to say, but it looks like network marketing is proving to be a good strategy.

As with all assessment, let’s start off with the easiest area to spot a scam THE PRODUCT!

Protandim Review – I cannot speak for the product since I’ve not yet tested it speak for the product. What I do know is I am more willing to try it than any other nutritional product I have seen recently due to the extensive clinical studies and peer reviewed studies that was used on it. More than twenty universities have started a number of self funded medical studies on the product in relationship to its relation on anti-aging and disease. Quite a few have been completed and are posted on www.pubmed.gov under Protandim to see.

In contrast to the majority of nutritional merchandise, Protandim is not an antioxidant by supplementation but rather a merchandise that activates the body’s production of its own natural enzymes which the body makes use of to tear down free radicals. Clinical studies appear to prove that it is many times more efficient than taking external antioxidants for this purpose. The LifeVantage corporate website () lists access to all the studies, information and news video releases on their product that explains how it acts and what it does.

What I like most regarding Protandim is the distinctive marketing approach it has

In constrast to many MLM companies which almost always use the old “try it out (for 30, 60 or 90 days) and see how you feel” script, LifeVantage distributors are able toconfidently exclaim that Protandim is clinically proven to lessen oxidative stress by slowing down the rate of cell aging to that of a 20 year old.

This alone is not enough to build a business on, but it’s a huge introduction for distributors. More often than not the hardest part in shaping a nutritional networking business is getting individuals to check out the product and LifeVantage holds the aces in this area.

I was pleasantly surprised at the price of the product. In an industry where product autoships are almost always above one hundred dollars per month, a one month autoship supply of Protandim for a retail “preferred customer” is only $39! This pricing is way less than the industry norm, thus making it doable to gain loyal retail consumers.

Besides the Protandim product, LifeVantage also has a skin care product called TrueScience which is a skin cream designed with the anti-aging properties of Protandim. What’s striking about the overall product line is its simplicity; just two fundamental products, with one core selling point, and a cost that is truly not expensive.

Ultimately it is going to take a lot more than research and advertising for a product to make it. Protandim will have to make a noticeable impression on the overall health of people taking it, whether it be additional energy, improved sleep, not getting sick as often, etc. There’s not a lot of individuals who will use their splurge on a product monthly based on research alone. If you are reading this article and have actually tried Protandim, please feel free give us comment on the product.

LifeVantage MLM compensation plan

I’m not going to go to the matter of how lucrative the MLM compensation plan is. There is quite a lot of money available in every MLM compensation plan as long as it’s legit. If you hear somebody going on about how their MLM comp plan pays the highest in the business, huge chance something is not right.

Technically speaking LifeVantage uses a unilevel pay plan paying down 9 dynamically compressed levels with the potential for a matching bonus on the 1st 4 levels and a coded bonus for LifeVantage pack qualifiers that allows for bonuses to be earned through unlimited depth. If none of this makes sense to you don’t worry about it.

The most important part about the MLM compensation plan is legal, because it only pays commissions on product sales. LifeVantage has taken an added step to promote the movement of product that I truly like and which does a lot to ensure legitimacy. Like all company, distributors must stay qualified to earn commissions, here in LifeVantage this means 200 PV per month in personal volume. The nice thing is that the volume generated from personal “preferred customers” reduces personal volume requirements for distributors. This means that as a distributor, I can reduce my monthly personal volume requirement down to the minimum of 30 PV if I have enough personal customers consuming product.

Behavior rewarded will be duplicated so when you see a company reward the enrollment of loyal retail “preferred customers” (individuals buying the product, but not does not involve themselves in the business opportunity), you will most likely have a higher customer to distributor ratio. This ratio is one of the most crucial things the attorney general and FTC look at when determining if a company is a pyramid scheme or not.

Company and Leadership of LifeVantage

There are a few notable points of interest about the LifeVantage beyond the short history I have mentioned. The company is a member of the Direct Selling Association () and the BBB (). They were implicated in and settled a lawsuit with Zrii. In this lawsuit, they were alleged to have conspired with ex- Zrii management/distributors to breach contracts and switch to companies. It was settled for 400,000 even if the lawsuit asked for damages of 250 million. This type of lawsuit is normal in the network marketing business and in my opinion nothing to be worried about.

As for the leadership behind the company, formerly with Metabolife, David Brown, is the CEO and Dr. Joe McCord, the driving force behind Protandim, is the Director of Science. It is noteworthy that Dr. McCord was the co-discoverer of antioxidant enzymes and their relationship to free radicals in 1968 at Duke University. It is also good to know that LifeVantage has skilled in-house legal counsel with Eric Marchant, who has counseled multi-national hundred million dollar network marketings in the past.

A quick look at the industry and competition

It is common knowledge that nutrition is the backbone of MLM industry and there is no doubt that the health and wellness industry is growing and will on the rise and will still increase. On the flipside I think at present you have an overload of companies coming into the industry and it is easy to get confused and be lost inside the rubble unless you have something exceptional I think LifeVantage has just that. With a low product price point and the type of studies and publicity behind Protandim, I think they are suited to thrive in the networking business.

In conclusion…

LifeVantage sells a legitimate product at a price point that real customers can afford and together with a compensation plan that for me solid more sturdy than your standard Multi-Level Marketing. While there is a lot of research and publicity behind this company you still want to be sure your belief is 100% behind it before delving into it. In multilevel marketing, belief in a product is still top priority and you cannot trade whatever amount of research for that. If you’re not willing to give it a year, then better if you don’t give it any other day at all. LifeVantage will work if you work it.

Roofing In Mesa AZ

In search of better adjustments on the roof, homeowners may try looking for a great roofing in Mesa AZ company. The theory behind this is the absolutely fantastic bargain. There are many of which the entire appearance of the home is transformed because more than 70 percent in the exterior is covered by the roof.

Confirm whether there’s a good roofing contractor for sale in your neighborhood. If you’re unclear about the expertise of the services, feel free to seek one in the Yellow Pages. Additionally, there are online pages whereby the search is going to be amplified with the suggestion in the forum boards, advantages and disadvantages from the service along with other informative segments in relevant topics regarding to roof maintenance.

An excellent supplier provides property owners with a resilient and strong choice of materials. If tiles are to your liking, then find a supplier with long-lasting protection in order to create better bang for your buck allocated to the renovation. Check to see the types of materials yourself if you need to. Usually the more pricey ones possess a better grip on the outer surface and handle the fluctuating weather with a lot of grit.

Another important feature may be the ever-so-capturing appearance with the tiles. Before agreeing to change of the overall look, make sure that the hues and texture don’t collide. The package should cover the used materials, replacement and cleaning or removal warranty in addition to insurance. The replacement and cleaning coverage depends upon the sum of money you want to invest upon.

Technically a single-story terrace house has smaller count of tiles and so the charges are somewhat minimal as compared to a double-storey bungalow. Glazed materials are also cost-risky as they have higher sustainability in substance. So these are a couple of the costs involved. Once you do the math with the costs you are ready to find your roofing in Mesa AZ!

The Advantages and Disadvantages of Push-fit Fittings

Different Types of Plumbing Fittings
– In the UK there are two ways in which most plumbing is done, the first and most common is done with copper pipe and fittings, the other is the newer plastic push fit system. The copper pipe and fittings has come under scrutiny recently as the joining of the copper pipes is increasingly
difficult as it is often time consuming and awkward due to the fact that copper pipe is often supplied in straight lengths meaning that it needs
to be joined or bent when ever a change of direction occurs. Plastics on the other hand, like that of the push fit system helps to eradicate this awkwardness. Push fit gives you a simple and easy way to make a joint without losing reliability and can be straightforwardly broken down and reassembled.

Advantages of Push-fit
– Plastic pipe is flexible; it is able to bend in a non-linear fashion. Copper piping has limited flexibility.
Plastic piping will not burst. Copper piping has a tendency to freeze and burst leaving huge amounts of damage making it harder to introduce this into
cold areas like cellars. Very much in contrast to plastic pipe.
Due to its flexibility plastic pipe can be pushed thought holes in joists rather than being laid in notches. This is not realistic with copper piping
as it is hard to get the holes in line.
Push fit systems can also be used with copper pipe when so desired as it is very adaptable.

Disadvantages of Push-Fit
– Due to its flexibility the plastic pipe will not support its own weight. This is will not jeopardize its ability to work however, but it would be difficult to poke a bent pipe through a hole in floor boards.
Plastic pipe cannot come into contact with anything that is very hot, for example a boiler. If in contact with a boiler there is a possibility that it could melt therefore it is advised that metal pipe work is used for the first few feet.
Aesthetically the plastic pipes are bigger and less attractive than its copper counter parts.
Plastic pipes and fittings are pricier than their competitor copper.

Availability
– Like that of the copper piping, plastic piping is available in both 15mm and 22mm diameter. They are available in a wide range of accessories
including: straight, right angled and Tee couplings. Washing machine taps, tap connectors, in-line stopcocks, one-way valves, stop ends and tank connectors.

Useful Suggestions
– If you don’t normally use plastic fittings it is certainly worth keeping some around, especially in the winter. If a pipe bursts you will be able to fix the problem in a matter of minutes and the effects will be long lasting.

Green Roofing

Continuing the theme of the importance of sustainable gardens, here we will discuss what are known as Green Roofs, the different types available and why they have become such an integral part of modern horticultural planning.

As one can ascertain from the name, the basic premise of a Green Roof is to bring plant matter, and therefore greenery, to our otherwise barren rooftops and thereby take best advantage of the dead spaces in and around our gardens, in order to better support our fast degrading environment.

Due to the nature of photosynthesis, Green Roofs are characteristically easy to establish and maintain because, by their very design, they are in the optimum position for the reception of sunlight and rainwater. The concept is not new ancient dwellings often used turf as a roofing material, but, in modern times, the Green Roof concept has once again been implemented in many commercial and architectural sectors, not to mention the broad following it has in the residential market. Rolls-Royces factory in West Sussex has one of the largest, commercial green roofs in Europe, covering over 32,000m2, and the green roofing project at the Ethelred Estate in London is another good example of the concept being taken more seriously.

The ecological ramifications of projects like these are self-explanatory, more green biomass equates to an increase in the conversion of CO2 to oxygen through photosynthesis, not to mention the purification of air borne moisture that comes into contact with the site. However, there are also great financial gains to made, which are probably best exemplified by the US Postal Distribution building in New York City which saves over $30,000 a year in heating and cooling. The project itself is designed to sustain itself for 50 years, which suggests a total of $1,500,000!

However, were getting ahead of ourselves – very few of us have the space and resources to oversee a project of such scale but, lest we forget, this is effectively an act of charity toward mother nature, and all charity begins at home.

Before you embark on a Green Roof project, it is imperative you check whether youll require planning permission to do so, and what regulation youll have to abide by. However, it is unlikely that youll be bound by many restrictions, as the state encourages their ecological benefits, particularly the green corridor it will provide for local wildlife. Regulations aside, the Green Roofs domestic applications are copious, including a cheap and sustainable form of insulation and greater control over storm water runoff. Research by the Centre for Sustainable Development at the University of Cambridge has found that “a layer of vegetation can reduce heat loss from buildings, cutting the wind chill factor by 75% and heating demand by 25%”, and the variety of plants you can grow are many – providing colourful coverings for otherwise boring, plain, or ugly roofs.

There are three categories of roof garden: extensive, semi-extensive and intensive. These are defined primarily by the depth requirement of their soil, thus dictating which plants are suited to each.

Extensive Green Roofs

Extensive category green roofs are characterized by their primarily artificial soil combinations that normally integrate materials such as perlite, rockwall, sand and concrete and, as such, they are best designated to drought resistant plants that are in need of good drainage rather than regular moisture. The planting medium is ordinarily supplemented by a filter layer, drainage layer, root barrier membrane and insulation and waterproofing respectively. Readymade Sedum mats enriched with substrate are a good choice for this environment. The planting medium itself should be no fewer than 2 inches deep.

Semi-extensive Green Roofs

The semi-extensive project needs a slightly deeper growing field (4-8 inches) as it should be able to support small perennial plants, though not the beds, trees and shrubs of the intensive green roof. Good plants to try here would be Knautia macedonica, Centaurea scabiosa and Origanum vulgare. As with the extensive roof, you will require all the standard drainage and waterproofing faculties that underpin the soil structure. A semi-extensive roof can take anywhere between twelve and eighteen months to establish and will require regular maintenance, particularly if it is situated at an unorthodox angle or position in relation to the sun. Regular weeding, watering and feeding are all a must, and even then you might find some areas may fail.

Intensive Green Roofs

An intensive Green Roof is that type which is most reminiscent of orthodox gardening, as it is often structured around three dimensions, including raised beds and box crops, and with a much wider range of suitable plants. However, these can only be supported by a richly organic growing medium and plenty of depth to become established – usually around 12 inches. It is important when constructing these raised beds that you use lightweight materials to ensure that the roof itself can support them. There are many other tricks that can be utilized to reduce the weight of the roof garden, such as the bulking out of compost with perlite, and using polystyrene rather than broken pots to crock the bottom of planters being used. However, as we know, the lighter the compost the less sturdy it acts as a plant anchor and pots and planters can easily fall over, but you can overcome this issue with clever placement of plant supports, such as wires and staking.

Floral and Hardy are experts in this field so if you would like to turn your unused flat roof into a colourful alpine meadow or an exotic Mediterranean-style vista, or you just want your own Hobbit house, just get in touch!

Roof Warranty So You Can Have Peace of Mind for Any Roofing Job

The roof is a very critical part of your Maryland home, and paying top dollar for its repair or replacement makes it a sizeable investment that you need to protect. One of the best ways to care for this investment is to make sure you get a warranty for the job. A warranty means that you wont have to pay this money again in case your roof fails within the warranty period.

There are two types of roof warranties: one for material and another for labor. A roof material warranty is provided by the manufacturer, while a labor warranty is provided by the contractor. The average warranty period for roof materials is between 20 to 30 years. For labor, warranty for faulty workmanship is around five years. If you encounter a roof warranty thats way beyond these time frames, then you should ask that it be extended straight away.

The goal of a warranty is to ensure quality roof installation that provides long-term performance. But relying on warranty alone is not enough. You have your own set of responsibilities to ensure that your roof remains problem-free; make periodic checks and clean off any debris. This allows you to see the condition of your roof.

Reputable roofing contractors will discuss roof warranty when you inquire about a roofing job or get an estimate. If the roof contractor did not mention warranty prior to the job, dont assume that its included because that is not always the case. Ask him about it so you can be assured that you have warranty for both materials and labor.

One of the most critical things you need to check on your roof warranty is the terms of acceptance. This defines the date when the warranty takes effect, which should be upon the completion of the job and not at the start of it. Most roofing MD manufacturers and contractors will send an inspector to check that the roof job is finished to confirm activation of the warranty.

A warranty is only as good as the roofing Maryland manufacturers and contractors that offer it. Some unscrupulous storm chaser roofing contractors descend upon a community after a storm, repair or replace roofs cheaply, never to be seen again. Make sure you check on them before they start work on your roof.

It is important to find a reliable roof company for your roofing needs. It may cost more, but a company that has been around for many years and with a good track record is always worth your every penny. For a list of Maryland roofing companies, please visit angieslist.com.

Bamboo Bench tops The Better Alternative

Every household home deserves a spectacular bench top, but have you ever considered bamboo instead of the typical pricey granite or marble?

Between wooden bench tops and marble bench tops there is a common annoyance for both. Marble bench tops, although provide a classy look to a kitchen can be extremely cold, particularly in winter. Wooden bench tops although make a kitchen look cozy and warm can become easily marked and damaged by heat and heated products. However, bamboo bench tops provide the perfect balance between marble and wood. Warm in winter, cool in summer and undamaged by heat, they are the perfect choice for your kitchen.

Bamboo bench tops are highly cost effective, but that doesnt mean quality is substituted. Brighten up any dull kitchen with this natural product and create a spectacular looking kitchen. The nodes on the bamboo plank accentuate the bamboo stalk and will add a beautiful natural glow to your kitchen.

Besides the aesthetical benefits, bamboo bench tops are extremely practical, durable and strong. Save money on coasters and mats, as bamboo bench tops are able to withstand heat. Move any hot pan or directly from your stove to your bamboo bench top without leaving a single mark. As the actual bamboo plant is not affected by heat or cold; neither is its product. Even areas that experience constant water exposure such as the sink will not harm your bench top. Although not completely proof, bamboo bench tops are fairly able to withstand scratching as well.

As our bench tops come in solid raw bamboo planks to prevent damage via transport, simply seal with any clear varnish found in any hardware store. Once sealed if there is a large build up of scratches over time simply sand it down and re-varnish for a brand new looking bench top.

Our bench tops are also safe from warping and shrinking and would make a cost effective, stunning but practical edition to your kitchen.

If interested, please visit our website.